Menu
Introduction
Sep 03, 2015 This video will illustrate how to replace the M.2 Solid State Drive in your ThinkPad X1 Carbon (2nd and 3rd Gen). If possible, back up your data before replacing the internal storage drive. Oct 24, 2015 In-depth review of the Lenovo ThinkPad Tablet 10 2nd Gen (Intel Atom x7 Z8700, Intel HD Graphics (Cherry Trail), 10.1', 595 ) with numerous measurements, benchmarks, and evaluations.
![Gen Gen](/uploads/1/2/4/6/124615419/301708789.png)
Use this guide to completely replace your mini's hard drive.
Note that some of the connections in this Mac are more fragile to disconnect and more difficult to reconnect than in other Macs. This guide is thorough in explaining how to remove each part that's in the way of the hard drive, but experienced repairers may be able to move the fan and the antenna plate out of the way without disconnecting them to save time.
- 2 mm Hex Screwdriver
- Mac Mini Logic Board Removal Tool
- Spudger
- T6 Torx Screwdriver
- T8 Torx Screwdriver
- 500 GB 5400 RPM 2.5' Hard Drive
- 1 TB 5400 RPM Samsung SATA Hard Drive (New)
- 500 GB SSD Hybrid 2.5' Hard Drive
- 500 GB SSD
- 1 TB SSD
- 250 GB SSD
- 500 GB SSD
- 1 TB SSD
- Place your thumbs in the depressions cut into the bottom cover.
- Rotate the bottom cover counter-clockwise until the white dot painted on the bottom cover is aligned with the ring inscribed on the outer case.
- You do not need to apply much downward pressure while turning.
- Tilt the mini enough to allow the bottom cover to fall away from the outer case.
- Remove the bottom cover and set it aside.
- Remove the two 11.3 mm T6 Torx screws securing the fan to the logic board near the antenna plate.
- Lift the ear of the fan nearest the RAM up off the standoff secured to the outer case.
- Removing the standoff screw is not necessary to remove the fan. You need only raise the fan enough to lift it off the standoff screw.
- Lift the fan out of the mini for enough clearance to access its connector.
- Grab all the wires at once and gently pull straight up to disconnect the fan from the logic board.
- Do not pry at the socket, or you may rip it from the logic board.
- Remove the fan.
- Remove the single 3.5 mm T6 Torx screw securing the cowling to the heat sink.
- Lift the cowling from the end nearest the antenna plate.
- Rotate the cowling away from the outer case and remove it from the mini.
- Remove the following screws securing the antenna plate to the mini:
- Two 6.6 mm T8 Torx screws
- Two 5.0 mm T8 Torx or 2.0 mm Hex screws (either screwdriver will work)
- When putting back together:
- It can be difficult to get the hard drive seated correctly such that the antenna plate fits in place correctly. If the screw holes don't line up with those on the hard drive, make sure that the two pins that are in the back of the hard drive are properly seated in the holes at the back of the case, above the housing for the second hard drive.
- The antenna attaches directly to the hard drive (red markers), therefore attaching the antenna can move the hard drive around and loosen the connection of the hard drive cable to the logic board.
- Slightly lift the antenna plate from the end closest to the RAM.
- Carefully pull the antenna plate away from the circular rim of the outer case.
- Do not remove the antenna plate yet. It is still attached to the AirPort/ Bluetooth board.
- Use the tip of a spudger to carefully pry the antenna connector up from its socket on the AirPort/Bluetooth board.
- Remove the antenna plate from the mini.
- Use the flat end of a spudger to pry the hard drive connector up from its socket on the logic board.
- Use the tip of a spudger to lift the IR sensor connector up and out of its socket on the logic board.
- This connector can be very fragile—lift gently and evenly.
- Remove the following three screws:
- One 5.0 mm T8 Torx or 2.0 mm Hex screw (either screwdriver will work)
- One 16.2 mm T6 Torx screw
- One 26 mm T6 Torx standoff
- To remove the logic board, the two cylindrical rods of the Mac mini Logic Board Removal Tool must be inserted into the holes highlighted in red. Inserting instruments into any logic board holes other than the ones highlighted in red may destroy the logic board.Homes listed on the website may be included in a special program and may not be available for sale. Freddie Mac takes reasonable steps to ensure that photographs and information we post on this website about a home offered for sale correctly depict or describe the home listed.However, Freddie Mac does not guarantee that any information is accurate, current or suitable for any particular purpose.Questions relating to particular homes shown on thesepages should be directed to the approved Listing Broker whose information appears with the home.
- Insert the Mac mini Logic Board Removal Tool into the two holes highlighted in red. Be sure it makes contact with the top side of outer case below the logic board before proceeding.
- Carefully pull the tool toward the I/O board. The logic board and I/O board assembly should slightly slide out of the outer case.
- Cease prying when the I/O board is visibly separated from the outer case.
- Remove the Mac mini Logic Board Removal tool.
- Simultaneously push the two plastic clips on the far left and right sides of the I/O board toward the middle of the I/O board and pull the I/O board away from the outer case.
- Only pull the logic board assembly out of the outer case until the edge of the I/O board is about .5' away from the edge of the aluminum outer case.
- Pull the hard drive away from the front edge of the mini and remove it from the outer case.
- Pull the hard drive away from the front edge of the mini and remove it from the outer case.
- During reassembly, there are two pins on the inside edge of the hard drive that fit into the case. The holes have rubber grommets around them, so it may be difficult to tell when you have seated the hard drive correctly.
- There are two pairs of holes in the case. Insert the pins into the holes closest to the bottom of the case.
- Remove the hard drive cable.
- There may be a sticker connecting this cable to the hard drive. If so, remove the sticker before attempting to remove the cable!
- Remove the two 6.2 mm T8 Torx screws from the side of the hard drive.
- Carefully peel the hard drive cover off the hard drive.
- Hard drive remains.
- If you are installing a new hard drive, we have an OS X install guide to get you up and running.
Manual Disk Discharge Mac 2nd Generation
To reassemble your device, follow these instructions in reverse order.
To reassemble your device, follow these instructions in reverse order.
301 other people completed this guide.
Embed this guide
Choose a size and copy the code below to embed this guide as a small widget on your site / forum.
Preview
I believe I have solved one problem. My wall-charger and associated USB-to-Shuffle cable is for my old V2 Shuffle. Silly me, the cable is externally identical to the one that came with the V4 Shuffle, so I just assumed it was compatible. Noooooo, it's not. Apple decided to change the internal wiring of the cable so the V3 and V4 Shuffles specifically require the new V3/V4 cable. I'm afraid to try the old charger with the new cable, but this apparently explains why my Shuffle won't charge on a V2 charger/cable. So, why, oh why in the world would Apple change the cable? Why doesn't Apple's V4 doc mention this, instead of letting the customer flail around trying to figure things out on their own? Why do the Apple folks at the store not know this? Why did the Apple phone support guy I spoke with not know this?
I'm still researching the charge and drain problems using the correct V3/V4 cable with my PC. Those problems are still a mystery.
Dec 10, 2015 2:44 PM